#CPS3 NOR Open SIMM (NOS) Reselase!!!
CPS3 NOS is an alternative to the original SIMMs, works similarly to Ultra SIMMs, allowing you to store up to 8 titles and switch between them using a DIP switch!
¡Feliz día de reyes!
github.com/herzmx/cps3-...
WIP: One more USB2DB15 with RPi Pico...
#CPS3 Game change test on custom SIMMs with dip swich.
P.S. I don't like so much cables....
#CPS3 custom NOR 128 SIMM working, flashed with OSCR too, TODO: more tests with full set of SIMMs
#cps3 WIP
I believe the tests are almost complete. The R/W Cartridge and SIMMs are functioning properly, so releasing the source code for anyone who may want to contribute. Note: I'm not an expert, just an electronics enthusiast...
https://github.com/herzmx/CPS3-OSCR-Adapter
Full BIOS R/W test on dead cartridges, 32/128M SIMM R/W tests complete, next is 64M SIMM, this with the original CD files concatenated for the 128Mbit/16MB SIMMs, write speed is quite acceptable now....
WIP CPS3 Cart Writer with OSCR...
Open Fight Stick with Pico Fighting Board, PS3, PS4, Switch, Xinput, NeoGeo+ WIP
https://github.com/OpenStickCommunity/Hardware/tree/main/Fightstick%20Case
JAMMA Linker with Xbox 360, 480p ok trisync monitor.
Algunos OSCR disponibles https://herzmx.mercadoshops.com.mx/
New revision of USB2DB15, but with NeoGeo port, this time it's custom to and printed in resin, thanks to @Raph_friend for this project...
WIP: JAMMA Splitter VS, to play in two cabinets at same time without Sega VS City ;)
* Right leves to stream or play in second cabinet
* Choose between P1 and P2 for any cab
* More test to do, but works...
USB-C power addon for current Open Source Cartdrige Reader, no more cursed micro USB
Ahora sí estamos más cerca, unas pruebas el fin de semana y esté pequeño batch estará listo 😅
New revision of NEO-MVS CHA/PROG-HB, R/W, this time no need extra ribbon to make more easy read/write/erase proces!
Now fully tested with special version of @240pTest to use all cartdrige capacity. Tested in MVS and AES with Fusion Converter, thanks to @furrtek for open proyect!
Happy New Year!
NEO-MVS CHA/PROG-HB, R/W support with external adapter, to keep costs low for end users, this is the second prototype and needs some improvements, but is working with @240pTest
One step more to replace SCART by VGA setup...
SEGA NAOMI CF Board Adapter to use with cheap CF to IDE-40 adapters, created with reference of https://wiki.pcbotaku.com/wiki/Sega_CF_box
https://oshpark.com/shared_projects/q8cTY7Zv
Working in @240pTest @BRCDEvg edition, SNES and Genesis, round 2...
Little USB helper to use with NAOMI CN12 port, next time Netboot from OrangePi Z2...
Finishing other proyect Sanni Cart Reader
Dump your carts, 🤔 and write some custom flash roms interesting for future proyects 😱...
https://github.com/sanni/cartreader
Ver bussy week MT32pi Lite ready...
Pico Fighting Board https://t.co/Tog1Mm1T6J… Less than 1ms of input lag with GP2040 firmware...
A lot of hard work, but i'm very satisfied with results, nice and clean RGBS + audio. Thanks @jeffqchen !!!
Perfect match to DB15-RGBS setup, thanks @jeffqchen @MartinHejnfelt
DB152USB thanks to https://gp2040.info project from @feral_ai, for use with NeoGeo stick 4/6 buttons and less than 1 ms of input latency, support XInput, DInput & Switch
MT32pi Lite solder less tests.
To avoid solder to RPiZ2 use little pongo pins, and little amout of solder in pins.
Hi @retrotink2, thanks for your great projects and for make Open the RetroTINK Ultimate. I really appasionate the DIY projects, i want to make a transcoder from RGBHV2Y'PbPr using your schematics, my doub is about the IC TLV3544, this can be replaced by TSH80+TSH82 or by OPA4863?
